The Stress–Strain Curve of Mild Steel: Every Point Explained
The stress–strain curve of mild steel is the single most-drawn diagram in Strength of Materials. Examiners ask you to draw it, label it, and explain each point. Here is the story the curve tells, in order.
The test
A round bar is pulled in a universal testing machine (UTM) with a slowly increasing tensile load.
- Stress = load ÷ original cross-sectional area (N/mm² or MPa)
- Strain = change in length ÷ original length (a dimensionless ratio)
Plot stress on the vertical axis and strain on the horizontal axis, and you get the curve.
Stage 1: the straight line (O to A)
For small loads, stress is directly proportional to strain. This is Hooke's law:
σ = E · ε
The slope of this line is Young's modulus E, a measure of stiffness. For mild steel, E is about 200 GPa (2 × 10⁵ MPa), and it is nearly the same for all steels.
- Point A, the limit of proportionality: the end of the straight line. Beyond it, stress is no longer proportional to strain.
Stage 2: the elastic limit (B)
- Point B, the elastic limit: the largest stress up to which the material returns completely to its original length when unloaded.
For mild steel, A and B are extremely close, so many books treat them as the same point. Strictly, the elastic limit can lie slightly beyond the proportional limit. The key idea: below B, deformation is recoverable.
Stage 3: yielding (C to D)
At a certain stress the bar suddenly starts to stretch a lot with almost no increase in load.
- Upper yield point (C): the stress at which yielding begins; the curve peaks and then drops.
- Lower yield point (D): the stress falls to a lower value and stays roughly steady while the strain increases significantly. The load barely rises while the bar elongates.
Mild steel is unusual in having this pronounced yield. Physically, the crystal planes in the metal start to slide over one another (plastic deformation). From here on, removing the load leaves a permanent set.
The yield stress is the most important design value. Structures are designed so that working stress stays well below it, usually using a factor of safety.
Stage 4: strain hardening (D to E)
After yielding, the steel hardens: the dislocations in the crystal structure tangle and block each other, so extra stress is needed for further strain. The curve rises again, now with a decreasing slope.
- Point E, the ultimate tensile strength (UTS): the highest point on the curve. It is the maximum engineering stress the bar reaches.
Stage 5: necking and fracture (E to F)
Past the UTS, the bar develops a local narrowing called a neck. All further elongation concentrates there. Because the area at the neck shrinks, the load needed falls, so the engineering stress (which uses the original area) drops.
- Point F, fracture: the bar breaks, typically in a "cup and cone" pattern for ductile steel.
Why does the curve fall if the steel is still getting stronger?
Because the standard curve uses the original area. If you computed stress with the actual, shrinking area, you would get the true stress–strain curve, which keeps rising right up to fracture. The engineering curve falls only because the denominator never changes.
Quick reference
| Point | Name | What it means |
|---|---|---|
| A | Limit of proportionality | Hooke's law stops holding |
| B | Elastic limit | Last stress with full recovery |
| C | Upper yield point | Plastic flow begins |
| D | Lower yield point | Steady plastic flow |
| E | Ultimate tensile strength | Maximum stress; necking begins |
| F | Fracture point | Bar breaks |
Ductile vs brittle (the follow-up question)
Mild steel is ductile: it shows large plastic strain and necking before breaking, giving visible warning. A brittle material such as cast iron or glass breaks with little or no plastic deformation, with no clear yield point and no necking. That is why steel is preferred for structures that must warn before failing.
Useful numbers and ideas to quote
- Typical mild steel: yield about 250 MPa, UTS about 400–500 MPa, with a percentage elongation of 20 % or more.
- Proof stress: metals without a clear yield point (aluminium, high-strength steels) use a 0.2 % proof stress, found by drawing a line parallel to the elastic slope from 0.2 % strain.
- Resilience is the area under the curve up to the elastic limit. Toughness is the total area up to fracture.
Sumantrak™ is an AI mentor built for Indian engineering, diploma, BCA and BSc CS/IT students — Strength of Materials, Material Science, and the rest of your syllabus, explained like this. Free to start →