Shear Force and Bending Moment Diagrams: Simply Supported Beam, Step by Step
Shear force (SF) and bending moment (BM) diagrams are the backbone of Strength of Materials and Structural Analysis. They tell you where a beam is most stressed, and therefore where to put the steel. The method never changes: reactions first, then cut the beam and balance.
The sign conventions (pick them and stick to them)
- Shear force: positive if it tends to rotate the left piece of the beam upward on the left cut (the usual "left up, right down is positive").
- Bending moment: positive if it makes the beam sag (compression on top, tension at the bottom). Sagging is positive, hogging is negative.
Your university may use a slightly different convention. Whatever it is, write it down at the top of the answer.
Example 1: UDL over the full span
A simply supported beam of span 6 m carries a uniformly distributed load w = 10 kN/m over its whole length.
Step 1: reactions
Total load = 10 × 6 = 60 kN. By symmetry:
R_A = R_B = 30 kN
Step 2: shear force at a section x from A
V(x) = R_A − w·x = 30 − 10x
| x (m) | V (kN) |
|---|---|
| 0 | +30 |
| 3 | 0 |
| 6 | −30 |
The SFD is a straight sloping line from +30 to −30, crossing zero at midspan.
Step 3: bending moment at a section x from A
M(x) = R_A·x − w·x²/2 = 30x − 5x²
| x (m) | M (kN·m) |
|---|---|
| 0 | 0 |
| 1.5 | 33.75 |
| 3 | 45 |
| 4.5 | 33.75 |
| 6 | 0 |
The BMD is a parabola, zero at both supports and peaking at midspan.
The key relationship
The bending moment is maximum where the shear force is zero (because dM/dx = V). Here V = 0 at x = 3 m:
M_max = wL²/8 = 10 × 36 / 8 = 45 kN·m
This formula is worth remembering for the exam, but show the working too.
Example 2: a point load off-centre
The same 6 m beam carries a 20 kN point load at 2 m from A (so 4 m from B). No UDL.
Step 1: reactions
Take moments about A:
R_B × 6 = 20 × 2 → R_B = 6.67 kN
R_A = 20 − 6.67 = 13.33 kN
(Check: moments about B give R_A × 6 = 20 × 4, so R_A = 13.33 ✓.)
Step 2: shear force
- From A up to the load (0 < x < 2 m): V = +13.33 kN, constant.
- At the load, the SF drops by 20 kN (a jump equal to the load): V = 13.33 − 20 = −6.67 kN.
- From the load to B (2 < x < 6): V = −6.67 kN, constant.
The SFD is two rectangles, one positive and one negative, with a vertical jump of 20 kN at the load.
Step 3: bending moment
- Between A and the load: M = 13.33·x, a straight line rising from 0 to 13.33 × 2 = 26.67 kN·m at the load.
- Between the load and B: M = 13.33·x − 20(x − 2), a straight line falling from 26.67 kN·m to 0 at x = 6. (Check at x = 6: 80 − 80 = 0 ✓.)
The BMD is a triangle, with its peak under the point load, because that is where the shear force changes sign.
What each loading does to the diagrams
| Loading | SFD shape | BMD shape |
|---|---|---|
| Nothing (between loads) | Horizontal | Straight sloping line |
| Point load | Vertical jump | Change in slope (a corner) |
| UDL | Sloping line | Parabola |
The shapes go up by one degree each step: load, then shear (one degree higher), then moment (one higher again). Remembering this lets you sketch the diagrams quickly and catch mistakes.
Common errors
- Wrong reactions. Always verify with the second moment equation or with ΣV = 0.
- Forgetting that the BM at a simple support is zero. If your diagram does not close to zero at the ends, there is an arithmetic slip.
- Calculating at too few points. For a UDL, at least three points are needed to draw a parabola convincingly.
- Not labelling. Mark values at the supports, at the load, and at the point of maximum moment.
Sumantrak™ is an AI mentor built for Indian engineering, diploma, BCA and BSc CS/IT students — Strength of Materials, Structural Analysis, and the rest of your syllabus, explained like this. Free to start →