← Mechanical blog
Concept guide16 October 2026 · 3 min read

Kirchhoff's Laws and Mesh Analysis: A Two-Loop Circuit Solved Completely

MechCivilEEEENTCR&AIEEEJ

Kirchhoff's laws are the first real tool in circuit analysis, and mesh analysis is the shortcut that turns them into a small system of equations. The same method works for a two-loop practice problem and a ten-loop industrial circuit.

The two laws

  • KCL (current law): the currents entering a node add up to the currents leaving it. Charge doesn't pile up at a node.
  • KVL (voltage law): going once around any closed loop, the voltage rises equal the voltage drops. Energy is conserved.

Mesh analysis uses KVL only. You assign a loop current to each independent loop, write KVL around each, and solve.

The circuit

Two loops sit side by side and share one resistor.

  • Mesh 1: a 10 V source, a 2 Ω resistor, and the shared 4 Ω resistor.
  • Mesh 2: the shared 4 Ω resistor, a 3 Ω resistor, and a 5 V source that opposes the direction of I₂.

Assume both mesh currents I₁ and I₂ flow clockwise.

The shared resistor carries both currents. In mesh 1 the drop across it is 4(I₁ − I₂), because I₂ flows through it in the opposite direction to I₁.

Step 1: KVL for mesh 1

Going round the loop in the direction of I₁: the source raises the voltage by 10 V, and the resistors drop it.

10 = 2·I₁ + 4(I₁ − I₂)
10 = 6·I₁ − 4·I₂              ... (1)

Step 2: KVL for mesh 2

In mesh 2, going in the direction of I₂: the shared resistor drops 4(I₂ − I₁), the 3 Ω drops 3·I₂, and the 5 V source opposes the current, so it acts like an extra drop:

0 = 4(I₂ − I₁) + 3·I₂ + 5
−5 = −4·I₁ + 7·I₂             ... (2)

Step 3: solve the two equations

Using determinants (Cramer's rule). The system is:

 6·I₁ − 4·I₂ = 10
−4·I₁ + 7·I₂ = −5

Determinant of the coefficients:

Δ = (6)(7) − (−4)(−4) = 42 − 16 = 26
I₁ = [ (10)(7) − (−4)(−5) ] / 26 = (70 − 20) / 26 = 50/26 = 1.923 A
I₂ = [ (6)(−5) − (−4)(10) ] / 26 = (−30 + 40) / 26 = 10/26 = 0.385 A

Both are positive, so both flow clockwise as assumed. (A negative answer would just mean the actual direction is opposite. It is not an error.)

Step 4: find the current through the shared resistor

I(4 Ω) = I₁ − I₂ = 1.923 − 0.385 = 1.538 A   (in the direction of I₁)

Step 5: check the answer

Substitute back into equation (1): 6(1.923) − 4(0.385) = 11.54 − 1.54 = 10.0 ✓

Substitute into equation (2): −4(1.923) + 7(0.385) = −7.69 + 2.69 = −5.0 ✓

A KCL check also works if you note the branch currents: the 4 Ω branch carries 1.538 A, and 1.923 = 1.538 + 0.385 ✓, meaning the current splits correctly at the junction.

Power check (the ultimate verification)

The 10 V source delivers 10 × 1.923 = 19.23 W. The 5 V source opposes I₂, so it absorbs 5 × 0.385 = 1.92 W rather than delivering it. Net power supplied = 19.23 − 1.92 = 17.31 W.

Power dissipated in the resistors:

  • 2 Ω: 1.923² × 2 = 7.396 W
  • 4 Ω: 1.538² × 4 = 9.467 W
  • 3 Ω: 0.385² × 3 = 0.444 W

Total = 17.31 W ✓. Supplied equals dissipated, which is the surest sign every number is right.

Tips for exam day

  1. Choose clockwise for every mesh. It makes the shared-resistor terms uniform: always minus the neighbour's current.
  2. Sources: ask "does the loop current flow out of the + terminal?" If yes, it is a voltage rise, otherwise a drop.
  3. Always do the substitution check. It takes one minute.
  4. Don't panic at negative currents. Report the direction in your final answer.

Mesh vs nodal

Mesh analysisNodal analysis
UnknownsLoop currentsNode voltages
Law usedKVLKCL
Best whenFew loops, voltage sourcesFew nodes, current sources

Sumantrak™ is an AI mentor built for Indian engineering, diploma, BCA and BSc CS/IT students — Basic Electrical Engineering, Network Analysis, and the rest of your syllabus, explained like this. Free to start →